Introduction

Threading your sewing machine is a pretty simple task. How to thread a singer 248 sewing machine? The needle and bobbin are easy to thread, but some steps may be confusing if you’re new at it—and they can take a while! In this article, we’ll walk you through each step of the process so that you don’t have any surprises when it comes time for you to thread your machine.

How to thread a singer 248 sewing machine? Thread the bobbin

• Thread the bobbin with a new length of thread.
• How to thread a singer 248 sewing machine 
• Put a piece of tape over the end of your sewing machine’s needle and thread it through one of its eye holes so that How to thread a singer 248 sewing machine it points up and away from you (see photo below).
• How to thread a singer 248 sewing machine
• Make sure there is no excess slack in either direction when you’re done winding on your new lengths of thread! How to thread a singer 248 sewing machine This will prevent them from getting tangled while sewing later on down the road when they’re being used as both eyes for two different machines simultaneously—you don’t want this happening to either one!
• Read More: Best sewing machine for auto upholstery
• 

insert the bobbin

When you insert the bobbin, it’s best to do so with your hands positioned underneath the machine and facing up. How to thread a singer 248 sewing machine thread will be on top of your fingers.

To place the bobbin in its compartment, gently push down on it until it clicks into place.

How to thread a singer 248 sewing machine ? Next, place a flat surface (like an ironing board) under each side of your sewing machine so that they’re not touching anything while they are off,,, and then make sure they’re centered between these two supports before closing both covers again!

Read More: best self-threading sewing machine

lift the bobbin thread

How to thread a singer 248 sewing machine? The first thing you need to do is lift the bobbin thread from the bobbin. You’ll need to hold it with your fingers and pull it through the eye of your needle, which will cause a lot of tension in this area. How to thread a singer 248 sewing machine, Next, guide that needle down into place on top of its presser foot so that you can see exactly where it belongs (you can see this by looking at Figure 6). Then take one hand and lower/lift either side of your sewing machine’s tension spring so that they’re both facing away from each other; this will help prevent them from accidentally pulling apart while working with multiple threads at once—if they did get too far away from each other then there wouldn’t be enough room left over for any more work!

guide it through the tense spring

• Lift the presser foot
• Guide the thread through the tension spring,How to thread a singer 248 sewing machine
• Lower the presser foot. Continue to guide it through the tension spring and take-up lever until you have threaded all three of these parts together.

thread the needle

• Thread the needle from the front of your machine.
• How to thread a singer 248 sewing machine?
• Thread the needle from the back of your machine.
• Thread the needle from below, to make it easier for you to see where you are going with this step later on in this process (and because it looks cool).
• 

lower the presser foot

To lower the presser foot, push the foot pedal. Dropping the needle into your fabric is done by lifting both handles at once. The hand wheel will raise your needle back up to its original position if you need to adjust it further before sewing. When finished, check that your needle is in place by turning either hand wheel until you feel it touch the bottom plate of the machine; then lift off presser foot (if not already done) and check again before starting the next seam or project!

you have to do many steps to thread your machine

• Thread the bobbin
• How to thread a singer 248 sewing machine? 
• Insert the bobbin and thread it through the tension spring
• Lift up on the bobbin thread to make sure that you can see where it is going (you want to be able to see what color)
• Guide this new piece of cloth through a small hole at one end of your machine, then pull it through until you have about 10 inches left over (this will be used later). Pull out any excess fabric from around your needle plate so there are no wrinkles on either side of your sewing machine needle plate when you put everything together later on in this step!

5/6/7/8 . . . etc., until all threads are pulled tight enough so that they won’t fall off during use but still leave room for movement within their respective zones; otherwise known as “stitching” or “sewing”.

Conclusion

So, there you have it. A step-by-step guide on how to thread your sewing machine correctly and safely. Hopefully, this has helped demystify the process for any newbies out there!